RICE DE-3C Pump Hydrostatic Piston Gas Briggs & Stratton

6 GPM 450 PSI

6 GPM 450 PSI Female Hose Swivel High Pressure Outlet Hose with QC Couplings 5.5 HP Honda or Briggs & Stratton Twin Piston, Positive Displacement Pump PARTS BREAKDOWN FOR MODEL DE-3C/DEH-3C RICE HYDRO INC. REF#.. PART NUMBER.. DESCRIPTION.. 2 HYPRO-2220-0013 PISTON CAP SCREW (QTY 2) 3 HYPRO-2270-0012 WASHER (QTY 2) 4 HYPRO-1830-0039 PISTON CUP SPREADER (QTY 2) 5 HYPRO-1410-0054 CUP BACKING PLATE (QTY 2) 7 HYPRO-1440-0005 PISTON GUIDE (QTY 2) 9 HYPRO-1410-0020 SUPPORT RING (QTY 2) 10 HYPRO-0503-5200 CONNECTING ROD 11 HYPRO-0602-5200 SAFETY COVER 12 HYPRO-2405-0006 GREASE FITTING ASSEMBLY 14A HYPRO-5003-5206 SUB ASSEMBLY SHAFT 14B HYPRO-5001-5206 COMPLETE SHAFT ASSEMBLY 15 HYPRO-1810-0001 RETAINER RING (QTY 2) 16 HYPRO-1600-0013 CRANKPIN RETAINER 17 HYPRO-1610-0005 KEY FOR SOLID SHAFT 20 HYPRO-1410-0006 SLINGER RING (QTY 2) 21 HYPRO-2005-0002 MAIN BEARING 22 HYPRO-2210-0062 CYLINDER HEAD BOLT (QTY 8) 23 HYPRO-0203-5200CB CYLINDER HEAD (QTY 2) 24 HYPRO-1720-0028 O-RING FOR CYLINDER HEAD (QTY 2) 25 HYPRO-1720-0019 O-RING FOR CYLINDER SLEEVE (QTY 2) 26 HYPRO-3550-0007 CYLINDER SLEEVE (QTY 2) 27 HYPRO-3400-0038 VALVE ASSEMBLY (QTY 4) 28 HYPRO-0100-5200C PUMP BODY 5206C 29 HYPRO-1510-0024 PUMP BASE ****** NA BRIGG-135252-1049-E3 5.5HP ENGINE W/GEAR REDUCTION NA HONDA-GX16OK1HX2 5.5HP ENGINE W/GEAR REDUCTION NA BALLVALVE-3/4 3/4" APOLLO BALLVALVE NA CHECKVALVE-3/4CON 3/4 CONBRACO F X F NA GAUGE-600 0-600 PSI LIQUID FILLED GAUGE NA FITTING-3/4-MPIPE RIGID END NA FITTING-3/4-MPX SWIVEL END NA HOSE-3/4X1250XFT CUSTOMER TO SPECIFY LENGTH NA CENTERDISK-LVJ-AUGER LOVEJOY CENTER DISC NA COUPLING-LVJ-3/4 3/4" COUPLING LOVEJOY NA COUPLING-LVJ-ENG-1" LOVEJOY 1" COUPLING NA LINESTRAINER-3/4 3/4" NYLON CAP STRAINER NA GASKET-3/4 GASKET FOR LINESTRAINER NA CAP-3/4 3/4" CAP FOR LINESTRAINER NA BOWL-3/4 3/4" BOWL FOR LINESTRAINER NA MESHSTRAINER-3/4 20 MESH LINESTRAINER 3/4 NA HYPRO-3375-0008 PULSE HOSE, REPLACES SURGE TANK NA HYPRO-5206C-FL TWIN PISTON 6 GPM 450 PSI NA SPRAY-6815-700-3/4 70-700 PSI REGULATOR NA SWIVEL-3/4 3/4 FIP X FGHT SWIVEL NA HOSEWASHER-3/4 3/4 HOSEWASHER NA COUPLERBODY-3/4 FEMALE CONNECT TO OUTLET HOSE NA COUPLERPLUG-3/4 MALE PUMP OUTLET PIPING ****** KIT HYPRO-3430-0037 PISTON REPAIR KIT--LEATHER: PISTON STACK PARTS KIT W/ LEATHER CUPS REF. #6 KIT HYPRO-3430-0039 PISTON REPAIR KIT--FABRIC: PISTON STACK PARTS KIT W/ FABRIC CUPS REF. #6 KIT PULSE-HOSE-KIT RETRO FIT KIT, SURGE TANK KIT SPRAY-AB6815-700 UNLOADER/BYPASS REPAIR KIT [if supportMisalignedColumns] [endif]

QUICK REFERENCE OPERATING INSRUCTIONS PISTON/PLUNGER/ROLLER PUMP SERIES First, make sure the pump is in proper working condition, i.e. gas, and oil levels, parts intact, etc. *Use 30 wt. Detergent Oil in engine and 90wt gear oil in gear reduction. Connect inlet hose. Unit may be suction, gravity, or force fed. Connect 8 foot high pressure hose to the outlet piping. Open the outlet ballvalve. Start motor. To preset test pressure or conduct a simulated test on unit, place a ballvalve on end of outlet hose and leave open. Start motor. Bleed air from system, thru hosebib or needlevalve. Close ballvalve on end of outlet hose and begin to build pressure. To adjust pressure relief valve turn clockwise to increase and counterclockwise to decrease. Open outlet ballvalve and unit will begin building pressure. Open needlevalve or hosebib to bleed excess air from piping. Once pressure is met, and the air is bled from the system, close the ballvalve on the unit, and turn off the engine/motor. Allow the test pump and the tested line to sit, holding pressure for your required test time. NOT FOLLOWING MANUFACTURER'S RECOMMENDED OPERATING INSTRUCTIONS MAY INVALIDATE ANY WARRANTY COVERAGE.

QUICK REFERENCE OPERATING INSRUCTIONS PISTON/PLUNGER/ROLLER PUMP SERIES First, make sure the pump is in proper working condition, i.e. gas, and oil levels, parts intact, etc. *Use 30 wt. Detergent Oil in engine and 90wt gear oil in gear reduction. Connect inlet hose. Unit may be suction, gravity, or force fed. Connect 8 foot high pressure hose to the outlet piping. Open the outlet ballvalve. Start motor. To preset test pressure or conduct a simulated test on unit, place a ballvalve on end of outlet hose and leave open. Start motor. Bleed air from system, thru hosebib or needlevalve. Close ballvalve on end of outlet hose and begin to build pressure. To adjust pressure relief valve turn clockwise to increase and counterclockwise to decrease. Open outlet ballvalve and unit will begin building pressure. Open needlevalve or hosebib to bleed excess air from piping. Once pressure is met, and the air is bled from the system, close the ballvalve on the unit, and turn off the engine/motor. Allow the test pump and the tested line to sit, holding pressure for your required test time. NOT FOLLOWING MANUFACTURER'S RECOMMENDED OPERATING INSTRUCTIONS MAY INVALIDATE ANY WARRANTY COVERAGE.